Magnetic swing torches
By ordering this item you will receive two torches with the magnetic system which allows them to be linked together.
Fire swing torch and staff:
These torches are made for the swing discipline. They are not meant to be throwned. Swinging is a discipline where torches are used with movements reminiscent of those practiced with poi or with GRS clubs .
Pair of swing torches which clip together using a magnet system. This means that during a show, you can form a fire staff with a flame at each end.
Each torch is equipped with a Kevlar length of 50cm. It is fixed with two screws, so that it can easily be changed. Note that the lifespan of the Kevlar is excellent. It is difficult to give an accurate estimate on how long wicks will last because it will depend on how you use them, but if you use your torches about once a week you will have several years of juggling ahead of you before you have to change your wicks.
These torches have a silicone sheath on the handle giving them a good grip, while playing a role of thermal insulation. The handles at the ends of the torches allow a good grip with the comfort necessary for performing rotational movements. The handles are made of wood so that they can slide easily in the hand without causing jerks.
Video of the swing torches:
Be ready to be astonished thanks to Valéry and the swing torches :-)
Technical characteristics of the torches:
- Length of a torch: 52cm.
- Staff length when torches are connected: 104cm.
- Total mass: 380g.
- Wicks: Kevlar.
NetJuggler's opinion on the magnetic torches:
- Pleasant torch to handle.
- The original wick is of high quality.
- A good lifespan for this torch.
- Nice visual.
The fact that you can, in a few seconds, switch from the use of two torches to that of a mini staff allows many new possibilities during shows. The magnetic connection is smooth but powerful enough to use the stick as a staff and even for throws.
Tips for using the magnetic torches:
Gora gives some advice to increase the lifespan of your torches. Professionals are used to this kind of instructions, but we never repeat them enough ...
When you soak your wicks, soak them 3/4, this will give the Kevlar time to absorb all the fuel and prevent it from leaking and running on the silicone. It is important to know that the silicone that makes up the grip of the handles is heat resistant but not flame resistant. Also, be careful not to let fuel run over the handles. This could encourage flames to spread over the silicone grip and cause your grip to warp or wear prematurely.
- Never use fuel such as White Spirit, Benzene or other alcohol based fuel. Prefer the use of flavorless oil which produces a very yellow so-called "cold" flame. If you have a blue or transparent flame, it means you are using the wrong fuel, so don't push it and check your fuel.
- Do not hold the torches in a static upright position with wicks facing down when ignited. Always keep them moving or in a horizontal position so that the flames do not damage the structure or the elements of your torches.
- Do not soak the silicone in the fuel.
Information about the manufacturer Gora Fire Juggling:
Gora is a premium fire equipment manufacturer and a renowned artist. He delivers here, as usual, an item both robust and comfortable to handle that will appeal to novices and professionals.
Hello, I bought them several years ago and when the time came to change the Kevlar I received them but I am struggling to put the screws back in the same place. Do you have any tips?
Thank you for your purchase, and I'm here to guide you through replacing your torch wicks. Here's a step-by-step, safe method for performing this on torches with thin metal cores: Preparation : Use a very fine metal drill bit, just a little wider than the wire end of a paper clip. Drilling: Drill the metal rods of the torch at the desired location: 2 holes will be sufficient per drill bit. Make sure the holes are clean and well positioned to facilitate the following steps. Installing the Paperclip Wire: Cut about 1.5 cm of paperclip wire. Insert the wire into the drilled hole so that half of it protrudes on each side of the rod. Fixing Kevlar: This paperclip wire will act as an anchor in the Kevlar mesh, preventing the wick from spinning or sliding along the torch. Use about 50cm of Kevlar in 5cm width for each torch head. You can now screw the screws into the Kevlar, without reaching the metal structure, thus ensuring a strong and secure fixing. Safety Tips: Take your time with this installation to ensure a clean and secure setup. This technique requires patience and attention to detail. Please do not hesitate to contact us if you need further assistance or have any other questions. We are here to help you use your equipment safely.
Hello, which wicks should I order to change them?
Thanks in advance.
You could use a 50mm wide flat wick. You can put about 50cm of wick on each head to get a similar look with the wicks in place on the torches as you receive them from us. But depending on your usage, you have one to several years before changing your wicks unless you use them very intensively. You don't have to buy replacement wicks right away.